6 LED
PROGRAMMABLE Multi Mode, Multi Voltage, Ultra Low Power
SIX LED BATTERY MONITOR
With Fitting Kit
Unit can be programmed to operate at 6v, 12v, OR 24v DC!!!
INDICATES ALTERNATOR, GENERATOR OR REGULATOR FAILURE
SIX Selectable 'voltage maps' - choose which suits your application best
Three indication modes - Bargraph, Single LED, or Flashing.
Good for any 6v, 12v, 24v battery where you want to monitor levels between the ranges specified in the tables below - Lead-Acid, Gel type or fibre mat technology cells.
Specifications :
-
Microprocessor controlled
-
Good for all Lead Acid, Gel, or AGM (Glass matt) batteries
-
NINE levels of indication from six red, yellow and green LEDs.
-
INDICATES BATTERY OVERCHARGE - protect your bike, car or system from overvoltage
- Voltage : SELECTABLE 6V, 12v, 24V (Max 30v). Accuracy to +/- 0.15v.
-
- SIX selectable voltage 'maps' to chose from for each of the 6,12,24v ranges. Settings retained after power off for 100 years.
-
-
THREE different display modes (bargraph, Single LED and flashing LED)
-
Low Power Consumption : 0.4mA in flashing mode, 3mA in single LED mode, 10mA maximum in multi led mode (all LEDs lit)
-
Just two wires to connect
-
Supplied with comprehensive printed instruction sheet
-
Size approx 49x23x20
The Details...............
Its annoying when your battery goes flat without warning. Or your regulator fails, and fries your electrics! This neat little unit can be used wherever you have a 6v, 12v, or 24v based electrical system. Perhaps your bike, car, camper or boat, golf buggy, or that battery you have to power the DC lighting in your shed can go flat on you without warning, or you would like some idea of how much juice you have left?
This compact gadget will show you by means of six bright LEDs the voltage level of your battery.
Simple fitment instructions are included with the device. A fitting kit comprising tie wrap and rear mounted adhesive pads and base is supplied to allow fitment to any flat or curved surface - fix to dashboard, wall, handlebars, any surface you can stick to or loop cable ties around.
In single LED mode, the LED will ‘travel’ to the current battery status level. In multi-LED mode, all LEDs will light to the current battery status level. In flashing LED mode, a single LED will 'blink' approx once per second to indicate current level, drawing an absolute mimimal power from your battery.
The red LED has multi-functional capability. Once the red LED illuminates, the battery is considered discharged. If further current is drawn, it may deep-discharge and reduce future battery life. User warning against further discharge is indicated by slow flashing, and critical level indicated by rapid flashing of the red LED.
If the system has an 'overcharge' state, for example, a motorcycle alternator regulator has failed, allowing a high voltage to be supplied to the battery and electrical system, the red and green LEDs will flash together to warn of possible impending damage to your electrical system.
The unit is simply programmed to the voltage and mode you need via the supplied comprehensive instructions.
Ranges: Unit can be set according to below tables. References to ‘Lead acid’ batteries below include Gel and AGM types.
|
Volts Map
|
Red/Gn
|
3rd Gn
|
2nd Gn
|
1st Gn
|
2nd Yellow
|
1st Yellow
|
Red
|
Rd Slw
|
Rd Fst
|
|
Display Mode
|
|
Battery Type
|
|
1 = Low Load
|
15.0
|
12.6
|
12.3
|
12.1
|
11.8
|
11.6
|
11.3
|
10.5
|
10.3
|
|
1 = Bargraph
|
|
1 = 6v
|
|
2 = Shallow
|
15.0
|
12.7
|
12.5
|
12.3
|
12.1
|
11.9
|
11.7
|
11.5
|
11.3
|
|
2 = Single
|
|
2 = 12v
|
|
3 = Standard
|
15.0
|
12.5
|
12.1
|
11.8
|
11.5
|
11.2
|
11.0
|
10.7
|
10.5
|
|
3 = Flash
|
|
3 = 24v
|
|
4 = Vehicle With Charging
|
15.0
|
13.2
|
12.5
|
12.0
|
11.7
|
11.4
|
11.0
|
10.7
|
10.5
|
|
|
|
|
|
5 = Medium Load
|
15.0
|
12.4
|
12.1
|
11.6
|
11.2
|
10.8
|
10.4
|
10.0
|
9.8
|
|
|
|
|
|
6 = Deep discharge
|
15.0
|
12.1
|
11.8
|
11.4
|
11.0
|
10.6
|
10.1
|
9.6
|
9.4
|
|
|
|
|
|
|
|
|
|
|
|
Note 1: For 24v, double the above values. For 6v, use half the above values.
|
|
|
|
|
|
Note 2: Refer to your battery’s data sheet especially if you wish to use other than range 1 to 4.
|
|
|
|
|
|
Note 3 : 0.4mA flashing, 3mA single LED, 10mA in ‘bargraph’ mode. Max 30v DC
|
|
|
|
|
|
|
|
|
|
|
